Epox-computer EP-6VBA Uživatelský manuál Strana 44
- Strana / 69
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
BIOS
EP-6VBA
Page 4-16
Reset Configuration Data:
This setting allows you to clear ESCD data..
The default is Disabled.
Disabled: Normal Setting.
Enabled: If you have plugged in some Legacy cards to the system and they
were recorded into ESCD (Extended System Configuration Data),
you can set this field to Enabled in order to clear ESCD.
CPU to PCI Write Buffer:
When enabled, up to four D words of data can be written to the PCI bus
without interruting the CPU. When disabled, a write buffer is not used and the
CPU read cycle will not be completed until the PCI bus signals that it is ready
to receive the data.
The Choice: Enabled, Disabled.
PCI Dynamic Bursting:
When Enabled, data transfers on the PCI bus, where possible, make use of the
high-performance PCI bust protocol, in which graeater amounts of data are
transferred at a single command.
The Choice: Enabled, Disabled.
PCI Master 0 WS Write:
When Enabled, writes to the PCI bus are command with zero wait states.
The Choice: Enabled, Disabled.
PCI Delay Transaction:
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI specifica-
tion version 2.1.
The Choice: Enabled, Disabled.
PCI #2 Access #1 Retry:
This item allows you enabled/disable the PCI #2 Access #1 Retry.
The Choice: Enabled, Disabled.
- TRADEMARK 1
- Technical Support Services 2
- BIOS Upgrades 2
- User Notice 3
- Section 5 Appendix 5
- Appendix A 5
- Appendix B 5
- Appendix C 5
- Appendix D 5
- Section 1 7
- INTRODUCTION 7
- Overview 8
- S.E.C. Cartridge Terminology 9
- Introduction 10
- Accelerated Graphics Port 10
- (AGP or A.G.P.) 10
- Hardware Monitoring 10
- Page 1-5 11
- EP-6VBA Board 12
- Power-On/Off (Remote) 12
- I/O Shield Connector 12
- Pentium II 13
- Processor 13
- Pentium III 13
- Page Left Blank 14
- Section 2 15
- FEATURES 15
- Page 2-2 16
- Section 3 17
- INSTALLATION 17
- EP-6VBA Detailed Layout 18
- Easy Installation Procedure 19
- Installation 20
- Section 3-2 20
- System Memory Configuration 20
- Memory Layout 20
- DIMM Module Installation 21
- Section 3-3 23
- Section 3-4 25
- Device Connectors 25
- Device Connectors (continued) 26
- 1-2 : Disabled 27
- 2-3 : Enabled 27
- (Default) 27
- Section 4 29
- AWARD BIOS SETUP 29
- 4-1 Standard CMOS Setup 30
- 4-2 BIOS Features Setup 31
- Page 4-4 32
- Page 4-5 33
- Page 4-6 34
- Page 4-7 35
- 4-3 Chipset Features Setup 36
- Page 4-9 37
- Page 4-10 38
- 4-4 Power Management Setup 39
- Page 4-12 40
- Page 4-13 41
- Page 4-14 42
- 4-5 PNP/PCI Configuration 43
- Page 4-16 44
- 4-6 Load Setup Defaults 45
- 4-7 Integrated Peripherals 45
- Page 4-18 46
- Page 4-19 47
- Page 4-20 48
- Page 4-21 49
- ROM PCI/ISA BIOS(2A6LGPAA) 50
- SENSOR AND CPU SPEED SETUP 50
- AWARD SOFTWARE, INC 50
- Page 4-23 51
- 4-9 Change Supervisor or 52
- User Password 52
- 4-10 IDE HDD Auto Detection 53
- Page 4-26 54
- 4-11 HDD Low Level Format 55
- 4-12 Save & Exit Setup 55
- 4-13 Exit Without Saving 55
- Appendix 58
- A-4 INTERRUPT MAP 58
- A-5 RTC & CMOS RAM MAP 59
- B-2 Unexpected Errors: 64
ARTHUR MARTIN ELECTROLUX ARD2841 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein ARTHUR MARTIN ELECTROLUX ARD2841.
Wir stellen 1 PDF-Handbücher ARTHUR MARTIN ELECTROLUX ARD2841 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentáře k této Příručce